Tygon® LP-1100
Tygon® LP-1100 - Gasoline Tubing meets EPA and CARB Emission Standards
Designed for Gasoline-Powered, Ground-Supported Equipment
Innovative Tygon® low permeation fuel tubing is designed to meet the EPA and CARB evaporation emission standards of 15mg/m2/day. Tygon® LP-1100 Tubing has superior resistance to fuels and industrial lubricants; the fluoropolymer liner is compatible with higher ethanol blend gasolines up to 100%. Its robust multi-layer design and construction is resistant to swelling, hardening and cracking caused by hydrocarbon-based fluids or sour gas. Tygon® LP-1100 Tubing is abrasion, cut and tear resistant for longer service life. Ideal for lawn and garden power equipment, small engine fuel lines as well as lubricating oil and grease transfer lines. Tygon® LP-1100 Tubing is ozone and UV light resistant. It is highly flexible, easy to install and offers excellent fitting retention. Tygon® LP-1100 Tubing is designed for fuel transfer line only, and is not recommended for fuel submersible applications. Features
Typical applications
• Small engine fuel transfer lines
• Lawn and garden power equipment
• Lubricating oil and grease transfer lines
• Lawn mowers
• Riding mowers
• Motorcycle
• Lawn and garden power equipment
• Lubricating oil and grease transfer lines
• Lawn mowers
• Riding mowers
• Motorcycle
Features and Benefits
- Conforms to new government regulatory standards for clean air
- Fluoropolymer liner compatible with higher ethanol blend gasoline
- Robust multi-layer design and construction
- Reduces hydrocarbon vapors escaping or permeating into the atmosphere
- Wide temperature range from -20 F to 180 F (-28.9 C to 82.2 C)
- Reduces photo-chemical smog
- High abrasion, cut and tear resistance for longer service life
- Compatible with 100% Ethan
Tygon® Tube LP-1100 - Diameters and wall thickness
| Art.No. | Ø Inner | Ø Outer | Wall | Inch rounded | Crossref. |
|---|---|---|---|---|---|
| TY2,03AY3,56 | 2,03 mm (2/25") | 3,56 mm (7/50") | 0,76 mm (3/100") | ||
| TY2,38AY4,76 | 2,38 mm (3/32") | 4,76 mm (3/16") | 1,19 mm (3/64") | ||
| TY3,18AY6,35 | 3,18 mm (1/8") | 6,35 mm (1/4") | 1,59 mm (1/16") | 3,2 x 6,4 x 1,6 mm | AY600007 |
| TY4,76AY7,94 | 4,76 mm (3/16") | 7,94 mm (5/16") | 1,59 mm (1/16") | 4,8 x 8,0 x 1,6 mm | AY600012 |
| TY6,35AY9,53 | 6,35 mm (1/4") | 9,53 mm (3/8") | 1,59 mm (1/16") | 6,4 x 9,6 x 1,6 mm | AY600017 |
Typical Physical Properties of Tygon® LP-1100 Tubing
| Property | ASTM Method | Value of Rating |
|---|---|---|
| Durometer Hardness | D2240 | 69° Shore A, 15s |
| Color | - | yellow |
| Specific Gravity | D792 | 1,29 |
| Water Absorption, 24 hrs. @ 23°C | D570 | 0.49% |
| Compression set Constant Deflection, 22 hrs. @ 70°C | D395 | Method B 65,00% |
| Tensile Strength | D412 | 16,5 MPa (2.400 psi) |
| Ultimate Elongation | D412 | 450,00% |
| Tear Resistance | D1004 | 29 kN/m (167 lb-f/In) |
| Tensile Stress @100% Elongation | D412 | 6,3 MPa (910 psi) |
| Tensile Set @75% Elongation | D412 | 50 |
| Maximum Recommended Operating Temperature | - | 82 °C (180°F) |
| Brittleness by Impact Temperature | D746 | -37°C (-35°F) |
Unless otherwise noted, all tests were conducted at room temperature 23°C (73°F). Values shown were determined on 1.905 mm (0,075") thick extruded strip or 1.905 mm (0,075") thick molded ASTM plaques or molded ASTM durometer buttons.
Product Characteristics
| Opacity | Flammability Rating | Fuel Permeation (total Tube) | |
|---|---|---|---|
| Translucent | UL 94 HB | CA Phase II, 40°C CE 10, 40°C | <15 g/m2/d <15 g/m2/d |
Regulatory Compliance
| 40 CFR 1060 EPA Regulation | Conforms |
| CA SORE Chapter 15, Article I | Conforms |
| CA Component Executive Order Number | Q-19-068 |
| CA Component Executive Order Size Limitations | 2/25" ID and above |
| EPA Certification Number | SGN-ENAPNR- 0A-03 |
| ANSI B175.2 Annex D Standard | Conforms |